Diagnostic Tools and Workshop Equipment

• Compact interface with galv. isolated CAN- and an RS232-interface on USB 2.0

Autocom CARS full adapter set for cars and light commercial vehicles.

• Test most engine sensors - lambda, mass airflow (MAF), MAP, ABS, TPS, camshaft/crankshaft position and etc;
• Test various actuators and solenoids;
• Observe fuel injector and fuel pump signals;
• View CAN bus signals;
• Basic primary and secondary ignition measurements.

• Test most engine sensors - lambda, mass airflow (MAF), MAP, ABS, TPS, camshaft/crankshaft position and etc;
• Test various actuators and solenoids;
• Observe fuel injector and fuel pump signals;
• View CAN bus signals;
• Basic primary and secondary ignition measurements.

• 9-pin locking adapter for use with older CAT engines.

• DPF Soot Level Resetter – CAT C3.3 / C3.8 (CAT 9 PIN Gray)

• Easy to use tool to reset DPF Soot Level in CAT C3.3 C3.8 Engines with DPF.
• 14 Pin CAT Connector

• Urea Level / Quality Sensor Emulator for CAT® C7.1 and Perkins® 1206F

• Diagnostic tool ready to use with Caterpillar and Mitsubishi forklift trucks.
• Tested and ready to use out of box

• DPF Emulator for CAT C3.3 & C3.8 Engines – Plug & Play

• SCR / DOC Emulator for Caterpillar C4.4 Acert Tier 4F Plug & Play

• Made in Canada. Original interface which safe to use with CAT machines.
• Supports Caterpillar machinery and engines up to 2023
• This is the only recommended communication device for CAT and the only one that has CAT Data Link (CDL) protocol required to properly communicate with CAT engines.

• CE39 is the industry's first four-in-one intelligent integrated device that integrates electric vehicle diagnosis, large/small electrical maintenance and inspection, and battery module charging, discharging, and equalization.

• The CAN 3 – CAN 1 Crossover Cable is designed to move J1939/CAN channel 3 diagnostic communications over to J1939/CAN channel 1.

CLAAS diagnostic cable 7 Pin to use with CLAAS CAN-USB Interface and CLAAS 4 CAN-WIFI Interface

CLAAS diagnostic cable 8 Pin to use with CLAAS CAN-USB Interface and CLAAS 4 CAN-WIFI Interface

• With the help of some optional features the CANUSB can be used for error monitoring and diagnostics
• Allow defects to be identified quickly and the on-board management system to be configured and updated

CLAAS diagnostic cable OBD2 to use with CLAAS CAN-USB Interface and CLAAS 4 CAN-WIFI Interface

• Best possible complete diagnostics and programming, troubleshooting, view diagnostic procedures and schemes for New Holland, CASE, KOBELCO, STEYR, FLEXICOIL

• Automatic machine for cutting keys XC-Mini Plus

• PC to EBS EB+
• For side of vehicle connection
• 6.5 m. Length

• PC to EBS EB+
• 15 m. Length

• PC to EBS EB+
• 20 m. Length

• EBS EB+ to DIAG+/Info-Centre
• For ECU → 08 2005
• Length 0.45 m

• PC to EBS EB+
• For direct ECU connection
• 6.5 m. Length

• PC to EBS EB+
• 6.5 m. Length

• EBS EB+ to DIAG+/Info-Centre
• 6.5 m. Length

The Cojali 50007006 Coolant Circuit Leak Test Kit is designed to pressurise vehicle cooling systems for quick and accurate leak detection in trucks, buses, and heavy-duty vehicles.

• OEM: 50007006
• Cojali reference: 50007006