License MB MEMO
The license allows to Read/Write FLASH and EEPROMs of MR (PLD) control unit.
It is possible to connect to the unit via:
- OBD (MR is mounted inside truck) or
- direct connection with DirectConnect 2 tool (MR is placed on your table).
This function is especially useful for chip-tuning works and recovering unit after the broken update. All operations are done via OBD, there is no need to decapsulate/open the unit, so unit stays in factory condition and therefore no warranty is voided.
This function allows cloning MR. You read one MR, save to *.bin file, and write it to another MR.
License MB KEYS
MB Keys learn - allows to add new keys for the MERCEDES truck over OBD. No additional equipment is used, all operations are done offline, the only connection to the truck required.
It is possible to make new key while connected to the unit via:
- OBD (MR is mounted inside truck) or
- direct connection with DirectConnect2 tool (MR is placed on your table).
IMMO OFF. Disable immobilizer in FR and MR.
License MB CALC
MB VeDoc and FDOK calculators - calculates access codes for VeDoc (X1, X2, X8.) and FDOK ( XT, XN, XA, XS) algorithms.
Must be used together with XENTRY (DAS) software and compatible diagnostic tool where these codes are asked. All operations are done offline, the only connection to the truck required for VEDOC.
For FDOK calculations not needed connection to the truck. FDOK code for new and old DAS.
DAS password generator - calculates password asked by DAS to access some special functions (MR downgrade from Euro 4, 5 to Euro 3 etc.)
License 2011+
The license allows accessing firmware 22B, 23E, 24B from 2011 year.
Continental Euro5 PLD: (MCU XC2287 (flash 768kB), 1 EEPROM M95640).
License 2014+
For PLD memory read and write operation (category memo) PLD with XC2287 secured microprocessor.
Open access Read & Write memory for PLD, made on 2011 and later, with microprocessor Infineon XC2287.
Software module support PLD with firmware versions: 21x, 23F, 24C, 25x, 26x.
License FR
The license allows accessing FR memory. Supported FMR; FR; FR/CPC; CPC1EU; CPC2EU. Immo off in FR.
Not supported: CPC2 NAFTA; CPC2+ NAFTA; CPC4 NAFTA; CPC3; ADM2; ADM3.
License MCM BSL (3Core)
A license for Read & Write IntFLASH; IntEEPROM; ExtEEPROM MCM1, MCM2 and ACM control units memory only over DirectConnect 2 tool.
Type 1. Continental MCM1 (MCU TC1796-256F / TriCore 1 EEPROM M95640) plastic.
Type 2. Continental MCM2 (MCU TC1796-256F / TriCore 1 EEPROM M95128) metallic
Note: DirectConnect2 tool is needed.
DirectConnect2
New generation DirectConnect tool (DC2) for different vehicle control modules programming without complete vehicle system.
ISP helps Read & Write unknown or damaged firmware from vehicle control units. BSL mode, TriCore BL mode, Motorola BKG mode, NEC serial BL ready.
Read/write PLD, MCM, FR, FFR. Learn a key for PLD, FFR. To have all options you need to have appropriative licenses.
License MAN KEYS
Add new keys for the MAN truck over OBD (or round connector (included)). No master key, no additional equipment is required. All operations are done offline, the only connection to the truck is required.
Key programming for MAN truck on FFR & PTM.
Models: TGA; TGL; TGM; TGX; TGS
Years: 1999 - 2014
IMMO pairing: FFR+EDC with additional Y cable DC2-FFR+EDC ;
Also, Key can be programmed with DirectConnect 2 tool connected to FFR or PTM.
Included adapter OBD2F-4-MN12 (round).
DirectConnect cable not included in license price. Only for VEI from V4 and software version 4.x
License MAN FFR
License MAN FFR allows to Read & Write FLASH & EEPROMs (C167 and ST10Fxx microprocessors) of drive control modules FFR (MAN).
Operations available over OBD connection or via DirectConnect 2.
Included adapter DC2-FFR. DirectConnect 2 tool not included.
License CRV
The license allows to Read/Write FLASH & EEPROMs of CRV1 & CRV2 engine control unit of Mercedes S, ML, GL class via OBD2.
License CR (CDI)
The license allows to Read/Write FLASH & EEPROMs of CDI engine control unit used in MB V-class, Sprinter and Vito thru the diagnostic port. CDI<>WSP pairing.
License DIAG
The license allows to Read DTC with the error description.
Clear DTC. Read and Erase fault codes.
VAN's on this moment not supported.
License EXTRA
Set a speed limit. Applicable for CPC drive control modules.
NOx torque limit. FR and CPC.
Erase exhaust faults (AdBlue system fault source repair must be done firstly).
License MCM2.1 BSL
License allows to Read / Write MCM2.1 (IntFLASH; IntEEPROM; ExtEEPROM) (unlocked) via DirectConnect2 tool in BSL mode. Supports MCM2.1 until 2016 year.
Note. DirectConnect 2 kit is needed with MCM adapter (not included).
Supported type: Continental MCM2.1 (MCU TC1797-512F / TriCore 1 EEPROM M95256)
License ADM BSL
The license allows to Read / Write ADM2, ADM3, VCU - Flash & EEPROM in BSL mode. External FLASH (AM29Fx00) and EEPROM R/W via DirectConnect 2 box ISP port and DC2-ADM adapter.
Functions available for ADM2 and ADM3. Supported all unknown (for Truck Explorer) versions and damaged ADM2, ADM3, VCU versions.
Note. DirectConnect 2 tool and DC2-ADM adapter not included.
License FR BSL
The license allows to MB FR1; FR2 - Flash & EEPROM Read / Write in Boot strap (BSL) mode. External FLASH (AM29Fx00) and EEPROM R/W in Boot mode. Via DirectConnect 2 box ISP port.
Functions available for old metallic FR0 and plastic FR1. In BSL mode Flash and EEPROM reading available for all version of FR firmware.
Supported all unknown (for Truck Explorer license FR) versions and damaged FR versions. Note. DirectConnect 2 tool, DC2-FR adapter, DC2-ISP1 cable are not included.
License CPC BSL
The license allows to Read / Write CPC0, CPC1 - Flash & EEPROM in Boot strap (BSL) mode. ST10Fxx internal FLASH and EEPROM. Via DirectConnect 2 box ISP port.
Functions available for CPC0 and CPC1. In BSL mode Flash and EEPROM reading available for all version of CPC firmware.
Supported all unknown (for Truck Explorer license FR) versions and damaged CPC versions.
Note: DirectConnect 2 tool, DC2-CPC adapter, DC2-ISP1 cable are not included.
License FFR BSL
License allows to Read / Write FFR - Flash & EEPROM in Boot strap (BSL)mode. External FLASH (AM29Fx00) and EEPROM R/W in Boot mode. Via DirectConnect 2 box ISP port.
Functions available for all FFR models. In BSL mode Flash and EEPROM reading available for all version of FFR firmware.
Supported all unknown (for Truck Explorer License FFR) versions and damaged FFR versions. Note: DirectConnect 2 tool, DC2-FFR adapter, DC2-ISP1 cable are not included.
License Android
Truck Explorer Android 2.1 license. For phones (tablets) we created Android mobile app: "Truck Explorer" More simple, more useful. The license is included, but the software must be purchased in a Google Play store.
Update/support subscription.
Update/support subscription for 12+1 months is included in a kit.