Premium Tech Tool Programming Functions
1 - Service and maintenance
17008-3 - Conversion kit
This operation is used to update vehicle data in
the central systems when replacing a control unit with a new part number.The
operation ensures that the correct information about the vehicle is stored in
the central system. This is important because the correct part number for
software/hardware must be available when programming the new control unit.
Select the part number for the new control unit
from the list.The control unit concerned must be programmed once this operation
has been performed.
17030-3 - Parameter, programming
This operation is used to read and program
parameter values.
17050-3 - Change component
This operation is used when replacing a component
in the vehicle.The operation reads off the information from the vehicle and
replaces the component in the central system along with the new components
serial number.
17051-3 - Retrieve component
This operation is performed to update the vehicle
with the correct information when installing a component.
17052-3 - Return component
This operation is used to return a component to
the central system.If a vehicle, where a component has been removed, is to be
returned to service, then a new component must be retrieved from the central
system.
Use operation: 17051-3 Retrieve component
17054-3 - Accessory kit
This operation is used to update vehicle data in
the central systems when ordering accessories.The operation ensures that the
correct information about the vehicle is stored in the central system. This is
important because the correct part number for software/hardware must be
available when programming the new control unit.
Enter the accessory kit part number.The control
unit concerned must be programmed once this operation has been performed.
2 - Engine, Engine mounting
and equipment
25801-3 - MID 233 Control unit, programming
This operation is used for programming the AdBlue
dosing system control unit.This operation must be used when replacing the
control unit. The operation reads the software and parameter settings from the
old control module and programs these settings into the new control module.The
operation is also used when reprogramming an existing control unit, for example
when a conversion kit has been ordered necessitating reprogramming of the
control unit.In the beginning of the operation you have three options:
- Use "Replace control unit" ONLY when
you change the control unit.
All data from the old control unit is transferred
to the new control unit.- Use "Reprogram control unit with complete
software package" ONLY when you need to repair the software in the control
unit.- Use "Reprogram control unit with only new parts of software
package" when you need to update control unit with new software. Only new
parameters or new parts of the software are programmed so this is normally the
fastest option. Note that this option is not available in Intermediate storage.
25802-3 - MID 233 Control unit, campaign
This operation is used in the campaign for
programming the AdBlue dosing system control unit. The operation can only be
performed when Volvo has issued a bulletin directing it.
27507-3 - MID 219 ECU, programming
This operation is used to program the (ACC)
control unit.This operation must be used when replacing the control unit. The
operation reads the software and parameter settings from the old control module
and programs these settings into the new control module.The operation is also
used when reprogramming an existing control unit, for example when a conversion
kit has been ordered necessitating reprogramming of the control unit.In the
beginning of the operation you have three options:
- Use "Replace control unit" ONLY when
you change the control unit.
All data from the old control unit is transferred
to the new control unit.- Use "Reprogram control unit with complete
software package" ONLY when you need to repair the software in the control
unit.- Use "Reprogram control unit with only new parts of software
package" when you need to update control unit with new software. Only new
parameters or new parts of the software are programmed so this is normally the
fastest option. Note that this option is not available in Intermediate storage.
27508-3 - MID 219 ECU, campaign
This operation is used to campaign program the
(ACC) control unit. (Adaptive cruise control) The operation can only be carried
out when Volvo has sent out a message about it.
28422-3 - MID 128 ECU, campaign
This operation is used for campaign programming
of the engine control unit.The operation can only be done when Volvo has issued
a bulletin about it.
28423-3 - MID 128 ECU, programming
This operation is used to program the engine
control unit.This operation must be used when replacing the control unit. The
operation reads the software and parameter settings from the old control module
and programs these settings into the new control module.The operation is also
used when reprogramming an existing control unit, for example when a conversion
kit has been ordered necessitating reprogramming of the control unit.In the
beginning of the operation you have three options:
- Use "Replace control unit" ONLY when
you change the control unit.
All data from the old control unit is transferred
to the new control unit.- Use "Reprogram control unit with complete
software package" ONLY when you need to repair the software in the control
unit.- Use "Reprogram control unit with only new parts of software
package" when you need to update control unit with new software.
Only new parameters or new parts of the software
are programmed so this is normally the fastest option. Note that this option is
not available in Intermediate storage.
3 - Electrical system and
instruments
35001-3 - MID 216 ECU, programming
This operation is used to program the exterior
Lighting Control Unit (LCM).This operation must be used when replacing the
control unit. The operation reads the software and parameter settings from the
old control module and programs these settings into the new control module.The
operation is also used when reprogramming an existing control unit, for example
when a conversion kit has been ordered necessitating reprogramming of the
control unit.In the beginning of the operation you have three options:
- Use "Replace control unit" ONLY when
you change the control unit. All data from the old control unit is transferred
to the new control unit.- Use "Reprogram control unit with complete
software package" ONLY when you need to repair the software in the control
unit.- Use "Reprogram control unit with only new parts of software
package" when you need to update control unit with new software. Only new
parameters or new parts of the software are programmed so this is normally the
fastest option. Note that this option is not available in Intermediate storage.
35002-3 - MID 216 ECU, campaign
This operation is used for campaign programming
of the exterior lighting control unit (LCM). This operation is only possible
when Volvo has sent the appropriate message.
36432-3 - MID 144 ECU, campaign
This operation is used to campaign program the
vehicle control unit.The operation can only be done when Volvo has issued a
bulletin about it.
36433-3 - MID 144 ECU, programming
This operation is used to program the vehicle
control unit.This operation must be used when replacing the control unit. The
operation reads the software and parameter settings from the old control module
and programs these settings into the new control module.The operation is also
used when reprogramming an existing control unit, for example when a conversion
kit has been ordered necessitating reprogramming of the control unit.In the
beginning of the operation you have three options:
- Use "Replace control unit" ONLY when
you change the control unit. All data from the old control unit is transferred
to the new control unit.
- Use "Reprogram control unit with complete
software package" ONLY when you need to repair the software in the control
unit.- Use "Reprogram control unit with only new parts of software
package" when you need to update control unit with new software.
Only new parameters or new parts of the software
are programmed so this is normally the fastest option. Note that this option is
not available in Intermediate storage.
36634-3 - MID 163 ECU, campaign
This operation is used for campaign programming
of the electronic start inhibitor.The operation can only be done when Volvo has
issued a bulletin about it.
36640-3 - MID 163 ECU, programming
This operation is used to program the
immobilizer.This operation must be used when replacing the control unit. The
operation reads the software and parameter settings from the old control module
and programs these settings into the new control module.The operation is also
used when reprogramming an existing control unit, for example when a conversion
kit has been ordered necessitating reprogramming of the control unit.In the
beginning of the operation you have three options:
- Use "Replace control unit" ONLY when
you change the control unit. All data from the old control unit is transferred
to the new control unit.
- Use "Reprogram control unit with complete
software package" ONLY when you need to repair the software in the control
unit.- Use "Reprogram control unit with only new parts of software
package" when you need to update control unit with new software. Only new
parameters or new parts of the software are programmed so this is normally the
fastest option. Note that this option is not available in Intermediate storage.
38104-3 - MID 140 ECU, campaign
This operation is used to campaign program the
instrument, centre module. This operation is only possible when Volvo has sent
the appropriate message.
38145-3 - MID 140 ECU, programming
This operation is used to program the instrument,
centre module.This operation must be used when replacing the control unit. The
operation reads the software and parameter settings from the old control module
and programs these settings into the new control module.The operation is also
used when reprogramming an existing control unit, for example when a conversion
kit has been ordered necessitating reprogramming of the control unit.In the
beginning of the operation you have three options:
- Use "Replace control unit" ONLY when
you change the control unit. All data from the old control unit is transferred
to the new control unit.- Use "Reprogram control unit with complete
software package" ONLY when you need to repair the software in the control
unit.
- Use "Reprogram control unit with only new
parts of software package" when you need to update control unit with new
software. Only new parameters or new parts of the software are programmed so
this is normally the fastest option. Note that this option is not available in
Intermediate storage.
38157-3 - MID 140 Programming, change language in
the instrumentation
This operation is used to change language in the
instrument, centre module.
38180-3 - MID 221 ECU, programming
This operation is used to program VDU/Secondary
Display.This operation must be used when replacing the control unit. The
operation reads the software and parameter settings from the old control module
and programs these settings into the new control module.The operation is also
used when reprogramming an existing control unit, for example when a conversion
kit has been ordered necessitating reprogramming of the control unit.In the beginning
of the operation you have three options:
- Use "Replace control unit" ONLY when
you change the control unit. All data from the old control unit is transferred
to the new control unit.- Use "Reprogram control unit with complete
software package" ONLY when you need to repair the software in the control
unit.- Use "Reprogram control unit with only new parts of software
package" when you need to update control unit with new software.
Only new parameters or new parts of the software
are programmed so this is normally the fastest option. Note that this option is
not available in Intermediate storage.
38181-3 - MID 221 ECU, campaign
This operation is used to campaign program
VDU/Secondary Display. The operation can only be carried out when Volvo has
sent out a message about it.
38374-3 - MID 140 Odometer, programming
This operation is used to program the odometer.
The operation is used to program the correct odometer reading for a replacement
control unit for the instrument.
39201-3 - MID 206 Control unit, campaign
This operation is used for campaign programming
of the Global Audio Platform ECU.
39202-3 - MID 206 Control unit, programming
This operation is used for programming the Global
Audio Platform ECU.This operation must be used when replacing the control unit.
The operation reads the software and parameter settings from the old control
module and programs these settings into the new control module.The operation is
also used when reprogramming an existing control unit, for example when a
conversion kit has been ordered necessitating reprogramming of the control
unit.In the beginning of the operation you have three options:
- Use "Replace control unit" ONLY when
you change the control unit. All data from the old control unit is transferred
to the new control unit.- Use "Reprogram control unit with complete
software package" ONLY when you need to repair the software in the control
unit.- Use "Reprogram control unit with only new parts of software
package" when you need to update control unit with new software.
Only new parameters or new parts of the software
are programmed so this is normally the fastest option. Note that this option is
not available in Intermediate storage.
39603-3 - MID 238 Control unit, programming
This operation is used for programming of Driver
Assistance control unit (DACU).This operation must be used when replacing the
control unit. The operation reads the software and parameter settings from the
old control module and programs these settings into the new control module.The
operation is also used when reprogramming an existing control unit, for example
when a conversion kit has been ordered necessitating reprogramming of the
control unit.In the beginning of the operation you have three options:
- Use "Replace control unit" ONLY when
you change the control unit. All data from the old control unit is transferred
to the new control unit.- Use "Reprogram control unit with complete
software package" ONLY when you need to repair the software in the control
unit.- Use "Reprogram control unit with only new parts of software
package" when you need to update control unit with new software.
Only new parameters or new parts of the software
are programmed so this is normally the fastest option. Note that this option is
not available in Intermediate storage.
39604-3 - MID 238 Control unit, campaign
This operation is used for campaign programming
of Driver Assistance control unit (DACU).The operation can only be done when
Volvo has issued a bulletin about it.
39732-3 - MID 203 Control unit, programming
This operation is used for programming the
telematic control unit, Dynafleet Driver Tool.This operation must be used when replacing
the control unit. The operation reads the software and parameter settings from
the old control module and programs these settings into the new control
module.The operation is also used when reprogramming an existing control unit,
for example when a conversion kit has been ordered necessitating reprogramming
of the control unit.In the beginning of the operation you have three options:
- Use "Replace control unit" ONLY when
you change the control unit. All data from the old control unit is transferred
to the new control unit.- Use "Reprogram control unit with complete
software package" ONLY when you need to repair the software in the control
unit.- Use "Reprogram control unit with only new parts of software
package" when you need to update control unit with new software.
Only new parameters or new parts of the software
are programmed so this is normally the fastest option. Note that this option is
not available in Intermediate storage.
39734-3 - MID 203 Control unit, campaign
This operation is used with campaigns for
programming the telematic control unit Dynafleet Driver Tool. The operation can
only be performed when Volvo has issued a bulletin about it.
39736-3 - MID 142 Control unit, programming
This operation is used to program the Volvo
LinkThis operation must be used when replacing the control unit. The operation
reads the software and parameter settings from the old control module and
programs these settings into the new control module.The operation is also used
when reprogramming an existing control unit, for example when a conversion kit
has been ordered necessitating reprogramming of the control unit.In the
beginning of the operation you have three options:
- Use "Replace control unit" ONLY when
you change the control unit. All data from the old control unit is transferred
to the new control unit.- Use "Reprogram control unit with complete
software package" ONLY when you need to repair the software in the control
unit.- Use "Reprogram control unit with only new parts of software
package" when you need to update control unit with new software.
Only new parameters or new parts of the software
are programmed so this is normally the fastest option. Note that this option is
not available in Intermediate storage.
39738-3 - MID 142 Control unit, campaign
This operation is used for campaign programming
of the Volvo link. This operation is only possible when Volvo has sent the
appropriate message.
39750-3 - MID 179 ECU, programming
This operation is used to program the FMS
Gateway.This operation must be used when replacing the control unit. The
operation reads the software and parameter settings from the old control module
and programs these settings into the new control module.The operation is also
used when reprogramming an existing control unit, for example when a conversion
kit has been ordered necessitating reprogramming of the control unit.In the
beginning of the operation you have three options:
- Use "Replace control unit" ONLY when
you change the control unit. All data from the old control unit is transferred
to the new control unit.- Use "Reprogram control unit with complete
software package" ONLY when you need to repair the software in the control
unit.- Use "Reprogram control unit with only new parts of software
package" when you need to update control unit with new software.
Only new parameters or new parts of the software
are programmed so this is normally the fastest option. Note that this option is
not available in Intermediate storage.
39751-3 - MID 179 ECU, campaign
This operation is used during a campaign to
program the FMS Gateway (FMS). This operation may only be carried out when
Volvo has sent out a message to this effect.
39775-3 - MID 141 Control unit, programming
This operation is used for programming the
telematic control unit, Dynafleet Driver Tool.This operation must be used when
replacing the control unit. The operation reads the software and parameter
settings from the old control module and programs these settings into the new
control module.The operation is also used when reprogramming an existing
control unit, for example when a conversion kit has been ordered necessitating
reprogramming of the control unit.In the beginning of the operation you have
three options:
- Use "Replace control unit" ONLY when
you change the control unit. All data from the old control unit is transferred
to the new control unit.- Use "Reprogram control unit with complete
software package" ONLY when you need to repair the software in the control
unit.- Use "Reprogram control unit with only new parts of software
package" when you need to update control unit with new software.
Only new parameters or new parts of the software
are programmed so this is normally the fastest option. Note that this option is
not available in Intermediate storage.
39776-3 - MID 141 Control unit, campaign
This operation is used during campaigns for
programming the telematic control unit, Dynafleet Gateway. The operation can
only be performed when Volvo has issued a bulletin about it.
4 - Gearbox
43205-3 - MID 130 ECU, programming
This operation is used to program the
transmission control unit.This operation must be used when replacing the
control unit. The operation reads the software and parameter settings from the
old control module and programs these settings into the new control module.The
operation is also used when reprogramming an existing control unit, for example
when a conversion kit has been ordered necessitating reprogramming of the
control unit.In the beginning of the operation you have three options:
- Use "Replace control unit" ONLY when
you change the control unit. All data from the old control unit is transferred
to the new control unit.- Use "Reprogram control unit with complete
software package" ONLY when you need to repair the software in the control
unit.- Use "Reprogram control unit with only new parts of software
package" when you need to update control unit with new software.
Only new parameters or new parts of the software
are programmed so this is normally the fastest option. Note that this option is
not available in Intermediate storage.
43221-3 - MID 222 ECU, programming
This operation is used to program the retarder
control unit.This operation must be used when replacing the control unit. The
operation reads the software and parameter settings from the old control module
and programs these settings into the new control module.The operation is also
used when reprogramming an existing control unit, for example when a conversion
kit has been ordered necessitating reprogramming of the control unit.In the
beginning of the operation you have three options:
- Use "Replace control unit" ONLY when
you change the control unit. All data from the old control unit is transferred
to the new control unit.- Use "Reprogram control unit with complete
software package" ONLY when you need to repair the software in the control
unit.- Use "Reprogram control unit with only new parts of software
package" when you need to update control unit with new software.
Only new parameters or new parts of the software
are programmed so this is normally the fastest option. Note that this option is
not available in Intermediate storage.
43253-3 - MID 223 ECU, programming
This operation is used to program the gear
selector control unit.This operation must be used when replacing the control
unit. The operation reads the software and parameter settings from the old
control module and programs these settings into the new control module.The
operation is also used when reprogramming an existing control unit, for example
when a conversion kit has been ordered necessitating reprogramming of the
control unit.In the beginning of the operation you have three options:
- Use "Replace control unit" ONLY when
you change the control unit. All data from the old control unit is transferred
to the new control unit.- Use "Reprogram control unit with complete
software package" ONLY when you need to repair the software in the control
unit.- Use "Reprogram control unit with only new parts of software
package" when you need to update control unit with new software.
Only new parameters or new parts of the software
are programmed so this is normally the fastest option. Note that this option is
not available in Intermediate storage.
43294-3 - MID 130 ECU, campaign
This operation is used for campaign programming
of the gearbox control unit.The operation can only be done when Volvo has
issued a bulletin about it.
43296-3 - MID 223 ECU, campaign
This operation is used for campaign programming
of the gear selector unit.The operation can only be done when Volvo has issued
a bulletin about it.
43298-3 - MID 222 ECU, campaign
This operation is used for campaign programming
of the retarder control unit. This operation is only possible when Volvo has
sent the appropriate message.
5 - Brakes
59315-3 - MID 136 ECU, campaign
This operation is used for campaign programming
of the brake control unit.The operation can only be done when Volvo has issued
a bulletin about it.
59354-3 - MID 136 ECU, programming
This operation is used to program the brake
control unit.This operation must be used when replacing the control unit. The
operation reads the software and parameter settings from the old control module
and programs these settings into the new control module.The operation is also
used when reprogramming an existing control unit, for example when a conversion
kit has been ordered necessitating reprogramming of the control unit.In the
beginning of the operation you have three options:
- Use "Replace control unit" ONLY when
you change the control unit. All data from the old control unit is transferred
to the new control unit.- Use "Reprogram control unit with complete
software package" ONLY when you need to repair the software in the control
unit.- Use "Reprogram control unit with only new parts of software
package" when you need to update control unit with new software.
Only new parameters or new parts of the software
are programmed so this is normally the fastest option. Note that this option is
not available in Intermediate storage.
6 - Wheel suspension and
steering
64717-3 - MID 184 ECU, programming
This operation is used to program the Rear axle
steering (RAS).This operation must be used when replacing the control unit. The
operation reads the software and parameter settings from the old control module
and programs these settings into the new control module.The operation is also
used when reprogramming an existing control unit, for example when a conversion
kit has been ordered necessitating reprogramming of the control unit.In the
beginning of the operation you have three options:
- Use "Replace control unit" ONLY when
you change the control unit. All data from the old control unit is transferred
to the new control unit.- Use "Reprogram control unit with complete
software package" ONLY when you need to repair the software in the control
unit.- Use "Reprogram control unit with only new parts of software
package" when you need to update control unit with new software.
Only new parameters or new parts of the software
are programmed so this is normally the fastest option. Note that this option is
not available in Intermediate storage.
64718-3 - MID 184 ECU, campaign
This operation is used to campaign program Rear
axle steering (RAS). The operation can only be carried out when Volvo has sent
out a message about it.
7 - Frame, springs, damping
and wheels
72886-3 - MID 150 ECU, campaign
This operation is used to campaign program Air
suspension, truck.The operation can only be done when Volvo has issued a
bulletin about it.
72888-3 - MID 150 ECU, programming
This operation is used to program the Air
suspension, truck. This operation must be used when replacing the control unit.
The operation reads the software and parameter settings from the old control
module and programs these settings into the new control module.The operation is
also used when reprogramming an existing control unit, for example when a
conversion kit has been ordered necessitating reprogramming of the control
unit.In the beginning of the operation you have three options:
- Use "Replace control unit" ONLY when
you change the control unit. All data from the old control unit is transferred
to the new control unit.- Use "Reprogram control unit with complete
software package" ONLY when you need to repair the software in the control
unit.- Use "Reprogram control unit with only new parts of software
package" when you need to update control unit with new software.
Only new parameters or new parts of the software
are programmed so this is normally the fastest option. Note that this option is
not available in Intermediate storage.
77610-3 - MID 166 ECU, programming
This operation is used to program the Tyre
pressure monitoring (TPM).This operation must be used when replacing the
control unit. The operation reads the software and parameter settings from the
old control module and programs these settings into the new control module.The operation
is also used when reprogramming an existing control unit, for example when a
conversion kit has been ordered necessitating reprogramming of the control
unit.In the beginning of the operation you have three options:
- Use "Replace control unit" ONLY when
you change the control unit. All data from the old control unit is transferred
to the new control unit.- Use "Reprogram control unit with complete
software package" ONLY when you need to repair the software in the control
unit.- Use "Reprogram control unit with only new parts of software
package" when you need to update control unit with new software.
Only new parameters or new parts of the software
are programmed so this is normally the fastest option. Note that this option is
not available in Intermediate storage.
77611-3 - MID 166 ECU, campaign
This operation is used during a campaign to
program the Tyre pressure monitoring (TPM). This operation may only be carried
out when Volvo has sent out a message to this effect.
8 - Body, cab and interior
87371-3 - MID 146 Control unit, programming
This operation is used for programming the
control unit for the electronic climate control.The operation is to be used
when replacing the control unit. The operation reads off the software and
parameter settings from the old control unit and then programs these settings
into the new control unit.The operation is also used when reprogramming an
existing control unit, for example when a conversion kit has been ordered
necessitating reprogramming of the control unit.In the beginning of the
operation you have three options:
- Use "Replace control unit" ONLY when
you change the control unit. All data from the old control unit is transferred
to the new control unit.- Use "Reprogram control unit with complete
software package" ONLY when you need to repair the software in the control
unit.- Use "Reprogram control unit with only new parts of software
package" when you need to update control unit with new software.
Only new parameters or new parts of the software
are programmed so this is normally the fastest option. Note that this option is
not available in Intermediate storage.
87372-3 - MID 146 Control unit, campaign
This operation is used during campaigns for
programming the electronic climate control unit. The operation can only be done
when Volvo has issued a bulletin about it.
88421-3 - MID 232 ECU, programming
This operation is used to program the airbag,
control unit.This operation must be used when replacing the control unit. The
operation reads the software and parameter settings from the old control module
and programs these settings into the new control module.The operation is also
used when reprogramming an existing control unit, for example when a conversion
kit has been ordered necessitating reprogramming of the control unit.In the
beginning of the operation you have three options:
- Use "Replace control unit" ONLY when
you change the control unit. All data from the old control unit is transferred
to the new control unit.- Use "Reprogram control unit with complete
software package" ONLY when you need to repair the software in the control
unit.- Use "Reprogram control unit with only new parts of software
package" when you need to update control unit with new software.
Only new parameters or new parts of the software
are programmed so this is normally the fastest option. Note that this option is
not available in Intermediate storage.
88422-3 - MID 232 ECU, campaign
This operation is used to campaign program of the
airbag, control unit. This operation is only possible when Volvo has sent the
appropriate message.
9 - Miscellaneous
90001-3 - MID 249 ECU, programming
This operation is used to program the Body
Builder Module.This operation must be used when replacing the control unit. The
operation reads the software and parameter settings from the old control module
and programs these settings into the new control module.The operation is also
used when reprogramming an existing control unit, for example when a conversion
kit has been ordered necessitating reprogramming of the control unit.In the
beginning of the operation you have three options:
- Use "Replace control unit" ONLY when
you change the control unit. All data from the old control unit is transferred
to the new control unit.- Use "Reprogram control unit with complete
software package" ONLY when you need to repair the software in the control
unit.- Use "Reprogram control unit with only new parts of software
package" when you need to update control unit with new software.
Only new parameters or new parts of the software
are programmed so this is normally the fastest option. Note that this option is
not available in Intermediate storage.
90002-3 - MID 249 ECU, campaign
This operation is used to campaign program the
Body Builder Module.The operation can only be done when Volvo has issued a
bulletin about it.